Quantum Superloader 3 Скачать руководство пользователя страница 30

Страница: 30 / 210

Chapter 2 Installation and Configuration

SCSI Bus Requirements

Quantum SuperLoader 3 User’s Guide

SCSI Bus Requirements

There are minor differences between the Quantum SuperLoader 3 LTO-2

and the Quantum SuperLoader 3 VS160/SDLT 600 autoloaders.

SuperLoader 3 LTO-2

You must connect the Quantum SuperLoader 3 LTO-2 to one of the

following SCSI bus types:

• Ultra2 SCSI Low-voltage Differential (LVD), Single-ended (SE) SCSI

bus

SuperLoader 3 VS160/SDLT 600

You must connect the Quantum SuperLoader 3 VS160 or the Quantum

SuperLoader 3 SDLT 600 to one of the following SCSI bus types:

• Ultra 320 SCSI-3, LVD SE SCSI bus
• Ultra 160 SCSI-3, LVD SE SCSI bus

General Information

Your SCSI host adapter card must also support the SCSI bus type used to

connect the autoloader. If you use a LVD SCSI bus, use a host adapter

card with a connection for a high-density (HD) 68-pin cable.

Note:

The autoloader is not compatible with a High-voltage

Differential (HVD) SCSI bus.

Note:

If you use a single-ended (SE) SCSI bus, the tape drive’s

performance is limited to the maximum data transfer speed of

the bus.

Note:

The maximum number of autoloaders supported per SCSI bus

is two.

Содержание Superloader 3



















































































































































































































Результаты поиска

Содержание Superloader 3

Отзывы:

Бренды по названию

Популярные бренды

Quantum Superloader 3, Руководство пользователя

Результаты поиска

Содержание Superloader 3

Отзывы:

Бренды по названию

Популярные бренды