Quantum Superloader 3 Скачать руководство пользователя страница 23

Страница: 23 / 210

Chapter 1 Introduction

Overview

Quantum SuperLoader 3 User’s Guide

SuperLoader 3 SDLT 600

This autoloader is SCSI-3 compatible and operates as a single SCSI ID/

two LUN data storage device.
The Quantum SuperLoader 3 SDLT 600 autoloader is equipped with a

Quantum SDLT 600 tape drive and contains up to sixteen SDLT II data

cartridges when utilizing two magazines, providing a compressed

capacity of 9.4 Terabytes and a sustained data transfer rate of 129.6 GB

per hour (native) or as high as 259.2 GB per hour compressed (assuming

2:1 compression).
The autoloader is compatible with the most popular operating systems

and environments supporting a 16-bit Ultra 160 SCSI-3 LVD interface but

requires direct support from the operating system or a compatible

backup application to take full advantage of its many features.

SuperLoader 3 DLT-S4

This autoloader is SCSI-3 compatible and operates as a single SCSI ID/

two LUN data storage device. It is also available as a Fibre Channel data

storage device.
The Quantum SuperLoader 3 DLT-S4 autoloader is equipped with a

Quantum DLT-S4 tape drive and contains up to sixteen DLTtape S4 data

cartridges when utilizing two magazines, providing a compressed

capacity of 25.6 Terabytes and a sustained data transfer rate of 216 GB per

hour (native) or as high as 432 GB per hour compressed (assuming 2:1

compression).
The autoloader is compatible with the most popular operating systems

and environments supporting an Ultra 320 SCSI-3 LVD interface but

requires direct support from the operating system or a compatible

backup application to take full advantage of its many features.
Fibre Channel can support up to 126 devices in a loop configuration.

Longwave transceivers (with Fibre Channel cable) support distances up

to 10 kilometers; short pulsewave transceivers (with Fibre Channel cable)

support distances up to 500 meters.
The Fibre Channel version of the SuperLoader 3 DLT-S4 operates at

speeds up to 4 Gigabits (Gb)/second.

Содержание Superloader 3



















































































































































































































Результаты поиска

Содержание Superloader 3

Отзывы:

Похожие инструкции для Superloader 3

Бренды по названию

Популярные бренды

Quantum Superloader 3, Руководство пользователя

Результаты поиска

Содержание Superloader 3

Отзывы:

Похожие инструкции для Superloader 3

Бренды по названию

Популярные бренды