Quantum Superloader 3 Скачать руководство пользователя страница 113

Страница: 113 / 210

Chapter 7 Customer Replaceable Units (CRUs)

Rack Mounting the Autoloader

Quantum SuperLoader 3 User’s Guide

General Preparation for
Rack Mount Installation

Take the following general safety steps before beginning a rack mount

installation.

Lower the cabinet feet.

Extend the cabinet anti-tip device, if available.

Ensure that the cabinet and all rack mounted equipment have a

reliable ground connection.

Verify that the total current of all rack mounted components

(including the SuperLoader) will not exceed the current rating of the

power distribution unit or outlet receptacles.

Secure the help of at least one other person. At least two people are

required to safely install the SuperLoader into a rack cabinet.

Stationary Rack Mount
Installation

This section describes the steps for attaching the autoloader directly to

the stationary rails of a rack.

Make sure you have the following tools and parts:
• #2 Phillips screwdriver
• Level
• The following autoloader accessory kit parts (see

figure 12

• Four autoloader brackets (two long and two short to

accommodate different rack depths)
Use the short autoloader brackets (74-60604-03) unless the

distance from the front mounting rail to the rear mounting

rail is less than 30.25 in. (76.84 cm).

• Two support brackets (74-60605-01)
• Eight 10-32 x 1/4 inch button head screws for the support

brackets (four per support bracket)

Warning:

Failure to take these safety steps may result in

personal injury or equipment damage.

Caution:

Do not remove the top cover of the autoloader during

the installation process. Removing the top cover could

result in damage to the autoloader.

Содержание Superloader 3



















































































































































































































Результаты поиска

Содержание Superloader 3

Отзывы:

Бренды по названию

Популярные бренды

Quantum Superloader 3, Руководство пользователя

Результаты поиска

Содержание Superloader 3

Отзывы:

Бренды по названию

Популярные бренды