Quantum Superloader 3 Скачать руководство пользователя страница 21

Страница: 21 / 210

Chapter 1 Introduction

Overview

Quantum SuperLoader 3 User’s Guide

SuperLoader 3 LTO-2

This autoloader is SCSI-3 compatible and operates as a single SCSI ID/

two LUN data storage device.
The Quantum SuperLoader 3 LTO-2 autoloader is equipped with a

Quantum LTO-2 tape drive and contains up to sixteen Ultrium 2 data

cartridges when utilizing two magazines, providing a compressed

capacity of 6.4 Terabytes and a sustained data transfer rate of 93.6 GB per

hour (native) or as high as 187.2 GB per hour compressed (assuming 2:1

compression).
The autoloader is compatible with the most popular operating systems

and environments supporting a Ultra 160 SCSI-3 LVD interface but

requires direct support from the operating system or a compatible

backup application to take full advantage of its many features.

SuperLoader 3 LTO-3

This autoloader is SCSI-3 compatible and operates as a single SCSI ID/

two LUN data storage device. It is also available as a Fibre Channel or

Serial Attached SCSI (SAS) data storage device.
The Quantum SuperLoader 3 autoloader is equipped with a LTO-3 tape

drive and contains up to sixteen Ultrium 3 data cartridges when utilizing

two magazines, providing a compressed capacity of 12.8 Terabytes and a

sustained data transfer rate of 245 GB per hour (native) or as high as

490 GB per hour compressed (assuming 2:1 compression).
The autoloader is compatible with the most popular operating systems

and environments supporting a Ultra 160 SCSI-3 LVD interface but

requires direct support from the operating system or a compatible

backup application to take full advantage of its many features.
Fibre Channel can support up to 126 devices in a loop configuration.

Longwave transceivers (with Fibre Channel cable) support distances up

to 10 kilometers; short pulsewave transceivers (with Fibre Channel cable)

support distances up to 500 meters.
The Fibre Channel version of the SuperLoader 3 LTO-3 operates at speeds

up to 2 Gigabits (Gb)/second.

Содержание Superloader 3



















































































































































































































Результаты поиска

Содержание Superloader 3

Отзывы:

Похожие инструкции для Superloader 3

Бренды по названию

Популярные бренды

Quantum Superloader 3, Руководство пользователя

Результаты поиска

Содержание Superloader 3

Отзывы:

Похожие инструкции для Superloader 3

Бренды по названию

Популярные бренды