Promax OL-612 Скачать руководство пользователя страница 91

Страница: 91 / 128

Page

October 2014

Sequential queue trigger function as below:

Function

Setting

Instruction

Source

BUS0

∼

BUS3

Select the trigger source from BUS0~BUS3.

Code

0x0000

∼

0xffff

“HEX”

∼

65535

“DEC”

Can be set discretionarily between 0x0000 and

0xffff “HEX”

or between 0 and 65535 (DEC) according to the

bus and code setting.

Add

Add the code type to the queue

Delete

Delete the code type from the queue

For example, to set a 16 bit data Bus signal, there will have 4 value as

0X9999, 0X9998, 0X9997, 0X9996 in the bus. We set BUS0 to include 16

measure channels and make above 4 values as trigger condition to observe

the data bus. Trigger setting follow up below steps:

Press "

Trigger menu

" and menu appears.

Press "

" till trigger mode display as "

Sequential Queue

Press "

" till signal source display as "

BUS0

Press "

" and data in code type as red background and green digital

indicator on, then insert data value "

0X9999

" and set code as

0X9999

". Press "

" again and red background disappeared. Repeat

operation of step D if setting error or need to be modified.

Press "

" and add setting value into the trigger queue, then info

window will display the value of "

0X9999

Repeat the operation of step

, and add "0X9998", "0X9997",

"0X9996" to trigger queue. Then info window will display value of

"0X9999", "0X9998", "0X9997", "0X9996".

Press "

" and delete the queue value if queue adding in error and

add again.

Turn "

Trigger level

" adjust knob or press "

set 50%

"till trigger

position display as "

NEXT T POS = 50%

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды