Promax OL-612 Скачать руководство пользователя страница 70

Страница: 70 / 128

October 2014

Page

Here are the procedures for carrying a self-calibration.

Disconnect all inputs, including probes and wires etc.

Press

UTILITY

to activate Function menu.

Press

next to Do Self-Cal.

Now there is a yellow window popping up to ask for a confirmation. Press F3

again, the Oscilloscope starts the self-calibration and yellow window remains the

calibration is done.

Please be ware that no contacts to any inputs channels

till the calibration is done.

►

SYS STAT (System State)

Press the

menu selection button and choose "

SYS STAT

" item. The menu

pops up in the screen as Fig. 61.

Figure 61.

SYS STAT Menu.

Function Menu

Setting Description

Horizontal

Show the horizontal parameter of the channel.

Vertical

Show the vertical parameter of the channel.

Trigger

Show the parameters of the trigger system.

Misc

Show the serial number and edition number.

After entering into the SYS STAT menu, choose the corresponding function, with

the corresponding parameters shown in the screen. If press the

selection button and choose the function item "

Horizontal

", the Horizontal

System State will be displayed in the screen. Press any other function button and

exit from the SYS STAT menu (see Fig. 62).

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды