Promax OL-612 Скачать руководство пользователя страница 2

Страница: 2 / 128

September 2014

SAFETY RULES

* The safety can turn compromised if there are not applied the instructions

given in this Manual.

Use the equipment only on systems or devices to measure the negative connected

to ground potential or off-grid.

This is a

class I

equipment, for safety reasons plug it to a supply line with the

corresponding

ground terminal

This equipment can be used in

Over-Voltage Category II

installations and

Pollution Degree 1

environments (see 2.3.-).

When using some of the following accessories

use only the specified ones

ensure safety:

Power cord

Probes

Observe all

specified ratings

both of supply and measurement.

Remember that voltages higher than

70V DC

33V AC rms

are dangerous.

Use this instrument under the

specified environmental conditions.

* The user is only authorized to

carry out the following maintenance operations:

Replace the mains fuse of the

specified type

and

value

On the Maintenance paragraph the proper instructions are given.

Any other cha

nge on the equipment should be carried out by qualified

personnel.

* The negative of measure

is at ground potential.

* Do not obstruct the ventilation system.

*

Follow the

cleaning instructions

described in the Maintenance paragraph.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды