Promax OL-612 Скачать руководство пользователя страница 67

Страница: 67 / 128

Page

October 2014

The description of the

Save Function Menu

is shown as the following table:

Function Menu

Setting Description

Source

CH1
CH2

MATH

Source of wave form to be saved.
Available sources: CH1,CH2,MATH.

WAVE

A , B

C , D

Location where selected waveform to be

saved or recalled.

Save

Action to save selected waveform to

selected location.

CH(X)

X=A,B,C,D

OFF

Turn Display on/off for selected and

stored waveform.

►

Save a Waveform

A sine wave form input CH1. Follow these steps to save waveform from

CH1.

Under WAVE SAVE MENU, press

next to Source to select CH1.

Press

next to WAVE to assign Location A for this waveform.

Press

next to Save to store the waveform captured from CH1.

►

Recall a stored waveform

Once the waveform is stored you can recall and display it on the screen. The

waveform would remain there until the next one is stored at the same

location, hence, the previous stored waveform would be overwritten by the

new one.

To recall a stored waveform, activate WAVE SAVE menu:

Press

next to Wave to select from one of four locations, the CH(X)

would show the location you've chosen.

Press

next to CH(X) to change to ON. Now you will see a stored

waveform displayed on the screen with whatever waveforms are

already on there.

Example to save/recall a waveform from location A. Fig.58.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды