Promax OL-612 Скачать руководство пользователя страница 15

Страница: 15 / 128

Page

October 2014

2.2.3

How to Implement the Function Inspection

Make a fast function check to verify the normal operation of the instrument,

according to the following steps:

Connect the Instrument to the Power and Push down the Power

Switch Button.

The instrument carries out all self-check items and shows the prompt

Press any Key Enter system

". Press the "

8 (UTILITY)

" button to get

access to the "FUNCTION" menu and push down F2 the menu selection

button to call out the function "Recall Factory". The default attenuation

coefficient set value of the probe in the menu is 10X.

Set the Switch in the Oscilloscope Probe as 10X and Connect the

Oscilloscope with CH1 Channel.

Align the slot in the probe with the plug in the CH1 connector BNC, and then

tighten the probe with rotating it to the right side.

Connect the probe tip and the ground clamp to the connector of the probe

compensator.

Press the "7(AUTOSET)" Button.

The square wave of 1 KHz frequency and 5V peak-peak value will be

displayed in several seconds (see Fig. 4).

Figure 5

. Auto set.

Check CH2 by repeating Step 2 and Step 3.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды