Promax OL-612 Скачать руководство пользователя страница 113

Страница: 113 / 128

Page

108

October 2014

4.2

Example 2: Working out the Gain of the Amplifier in the

Metering Circuit

The purpose of this example is to work out the Gain of an Amplifier in a Metering

Circuit. First we use Oscilloscope to measure the amplitude of input signal and

output signal from the circuit, then to work out the Gain by using given formulas.

►

Step1

Go to both CH1 menu and CH2 menu and then their Probe menu to set

attenuation coefficient as 10X, turn the switch on the Probe to 10X as well.

►

Step2

Connect the Probe through Channel 1 to the signal source the input signal in the

circuit. And Probe 2 through Channel 2 to its signal source the output signal in

the circuit.

►

Step3

Press AUTOSET button to let oscilloscope run through a pre-set function and

apply them to both signals coming into Channel1 and Channel 2.

►

Step4

Press

MEASURE

to activate measurement function menu.

Press

next to Source to highlight Source.

Press

to set Source as

CH1

Press

to set Source as

CH2

Press

to highlight

Type

Press

to set

Press

to set

Get

readings of Channel 1 and Channel 2. (see Fig. 104).

Calculate the amplifier gain with the following formulas.

Gain = Output Signal / Input signal

Gain (db) = 20×log (gain)

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды