Promax OL-612 Скачать руководство пользователя страница 124

Страница: 124 / 128

October 2014

Page

119

50% level setting(typical)

Input signal frequency ≥50Hz.

Edge trigger

Slope

Rising, Falling

Sensitivity

0.3 div.

Pulse trigger

Trigger condition

Positive pulse > <,

; Negative pulse > <,

Pulse Width range

24 ns ~ 10 s.

Video Trigger

Modulation

Support standard NTSC, PAL and SECAM broadcast systems.

Line number range

1-525 (NTSC) and 1-625 (PAL/SECAM).

Slope Trigger

Trigger condition

Positive pulse > <,

; Negative pulse > <,

Time setting

24 ns ~ 10 s.

Alternate Trigger

Trigger on CH1

Edge, Pulse, Video, Slope.

Trigger on CH2

Edge, Pulse, Video, Slope.

LOGIC ANALYZER

Sampling rate

20 S/s

∼

1 GS/s

Input channel

16.

Max Storage

4 M/Channel, 16 K (when only sampling rate is 250 MS/s,

500 MS/s, 1 GS/s)

Measurement bandwidth

200 MHz.

Input impedance

600 K

5 % // 15

5 pF

Threshold level

-6 V

∼

+6 V.

Input signal range

-30 V

∼

+30 V

Trigger position setting

Pre-trigger, mid-trigger, re-trigger.

Trigger Mode

Edge trigger, Bus trigger, Pattern trigger, Sequential queue data

,Distributed queue trigger, Data width queue trigger.

Data Search

Support.

Data System

Binary system, Decimal system, Hex.

Digital Filter

0/1/2 optional.

Setting storage

Support.

USB storage

Support.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды