Promax OL-612 Скачать руководство пользователя страница 17

Страница: 17 / 128

Page

October 2014

2.2.5

How to Set the Probe Attenuation Coefficient

The probe has several attenuation coefficients, which will influence the vertical

scale factor of the oscilloscope.

If it is required to change (check) the set value of the probe attenuation

coefficient, press the function menu button of the channels used, then push down

the selection button corresponding to the probe till the correct set value is

shown.

This setting will be valid all the time before it is changed again.

NOTE

The attenuation coefficient of the probe in the menu is preset to 10X

when the oscilloscope is delivered from the factory.

Make sure that the set value of the attenuation switch in the probe is the same

as the menu selection of the probe in the oscilloscope.

The set values of the probe switch are 1X and 10X (see Figure 7).

Figure 8.

Attenuation Switch.

NOTE:

When the attenuation switch is set to 1X, the probe will limit the

bandwidth of the oscilloscope in 5MHz. If it is needed to use the

whole bandwidth of the oscilloscope, the switch must be set to 10X.

2.2.6

How to Use the Probe Safely

The safety guard ring around the probe body protects your finger against the

electric shock, shown as Figure 8.

Figure 9.

Finger Guard.

Содержание OL-612

































































































































Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды

Promax OL-612, Руководство пользователя

Результаты поиска

Содержание OL-612

Отзывы:

Бренды по названию

Популярные бренды