Precisa XB series Скачать руководство пользователя страница 69

Страница: 69 / 73

14 Further information

■

14.2.4 Automatic calibration

For an automatic calibration with the built-in calibration weight “SET

CALIBRATION MODE AUTO” must be selected in the configuration

menu (see Chapter 5.6 “Calibration functions”).
The balance now calibrates itself automatically every 24 hours and/or

after each temperature change of 3 degrees Celsius, depending on the

definition in the configuration menu “SET CALIBRATION AUTOCAL”.
The time of the automatic calibration is as determined in the configu-

ration menu under “SET CALIBRATION AUTOCAL. -TIME n h”.

(e.g. 6 h for 06.00 o'clock in the morning).

NOTE

For the automatic calibration by time and by time/temp. the date

and time of the balance must first be correctly set (see Chapter 5.9

“Date and time”).
The calibration can also be effected manually any time while auto-

calibration is activated.
The automatic calibration then takes place only if no weight is pla-

ced on the pan for at least five minutes.
It is recommended, that the time for the auto-calibration be set at

a time outside the normal business hours (for example, in the early

morning).

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 69 / 73

Результаты поиска

Содержание XB series

Отзывы: