Precisa XB series Скачать руководство пользователя страница 68

Страница: 68 / 73

■

14 Further information

Then proceed as follows:

14.2.3 Internal calibration

For an internal calibration with the built-in calibration weight “SET

CALIBRATION MODE INTERNAL” must be selected in the configura-

tion menu (see Chapter 5.6 “Calibration functions”).
Then proceed as follows:
• Switch to “BALANCING” with the «

MODE

»-key

• Press «

» until “CALIBRATION” is shown.

• The calibration is finished after a certain period of time.

• Switch to “BALANCING” with the

MODE

»-key

cALIBRation

• Press «

» until “CALIBRATION”

appears.

- - 0000

• The balance carries out a Zero

measurement (0000 g is shown

flashing)

- - 372

• After the zero measurement the

display flashes with the previous-

ly entered calibration weight

• Place the calibration weight on

the pan

- - 372

• The display flashes rapidly
• Calibration is complete when the

display stops flashing (the exact

weight is shown)

+ 372.15

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 68 / 73

Результаты поиска

Содержание XB series

Отзывы: