Precisa XB series Скачать руководство пользователя страница 57

Страница: 57 / 73

10 Practical examples

■

10.1.3 Setting the Print functions

In order to alter the print parameters proceed as follows:

• Press «

MODE

» again and hold down the button until the next print

function appears. Change the setting in the same way.

• Press «

PRINT

» to return to “SET DATA PRINT”.

• Press «

PRINT

» again to exit menu.

SET DATA PRINT

• Press «

MODE

» and hold down

until “SET DATA PRINT” appears.

• Release the «

MODE

»-button.

AUTO-START OFF

• Press «

MODE

» briefly. “AUTO-

START ...” will appear.

AUTO-START ON

• Press «

MODE

» repeatedly, until

the desired setting is displayed

(ON or OFF will flash).

mODE STABLE

• Press «

MODE

» and hold down the

button until the next print

function appears (“MODE ...”).

• Release the «

MODE

»-button.

MODE TIMEBASE

• Press «

MODE

» repeatedly, until

the desired setting is displayed.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 57 / 73

Результаты поиска

Содержание XB series

Отзывы: