Precisa XB series Скачать руководство пользователя страница 14

Страница: 14 / 73

■

2 Your balance

2.2

Application, conformity, labelling

2.2.1 Correct use of the balance

The balance may only be used for the weighing of solid-materials and

of liquids filled into secure containers.
The maximum allowable load of the balance must never be exceeded,

otherwise the balance may be damaged.
In using the balance in combination with other appliances made by

Precisa as well as with appliances produced by other manufacturers,

the current regulations for the safe use of the relevant attachments

and their application in accordance with instructions must be obser-

ved.

2.2.2 Conformity

The balance has been manufactured and tested in accordance with

the standards and recommendations set out in the enclosed certificate

of conformity.
The power adaptor produced for the operation of the balance and

intended exclusively for this application, complies with the electrical

protection class II.

2.2.3 Labelling

Label

Location of label

Manufacturer's name-

plate (1)

Casing-front, middle

Nameplate (2)

Casing-front, left

Weighing range (3)

Casing-front, right, first column

Calibration value (4)

Casing-front, right, second column above

Readability (5)

Casing-front, under the calibration value

Model plate (6)

Casing-underside, centre rear

Serial No. plate (7)

Casing-rear, left, under the bubble level

Tab. 2.1 List of appliance labels

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 14 / 73

Результаты поиска

Содержание XB series

Отзывы: