Precisa XB series Скачать руководство пользователя страница 25

Страница: 25 / 73

4 Modes of operation and operating

■

4.4

Significance of the two main menus

The balance has two main menus available: the configuration menu

and the application menu.
The basic-program of the balance is defined in the

configuration

menu

. With this, you can either work with the basic-configuration

programmed ex-works, or define and store a user-configuration

adapted to your specific needs.
In the

application

menu

, you define a working program, which is

suited to the specific weighing problem.

4.5

Activating the two main menus

4.5.1 Activating the configuration menu

• Press «

ON/OFF

» to switch on the balance.

• Continue to hold down the «

MODE

» button during the start-up

process (approximately 10 seconds), until the currently set

language appears.

• Now you can change the configuration menu.

4.5.2 Activating the application menu

• After the start-up process has finished, press «

MODE

» until “SET

APP. ...” appears on the display. You are now in the application

menu.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 25 / 73

Результаты поиска

Содержание XB series

Отзывы: