Precisa XB series Скачать руководство пользователя страница 38

Страница: 38 / 73

■

5 Working with the configuration menu

5.9

Date and time

To activate the menu see Chapter 4.5 “Activating the two main me-

nus” and Chapter 4.6 “How the menu control operates”.

5.10 Password protection

To activate the menu see Chapter 4.5 “Activating the two main me-

nus” and Chapter 4.6 “How the menu control operates”.

The password protection permits you to protect the application menu

and/or the configuration menu against unintentional changes.
See Chapter 4.7 “Password protection of the menus” and

Chapter 10.1.4 “Activation of password protection” for further

information on password protection.

• SET

DATE AND TIME

DATE [DD.MM.YY]

TIME

[HH.MM.SS]

FORMAT

STANDARD

/US

Set date and

time

NOTE

These settings are only available if the clock is installed.
The date and time display continues in the event of a power failure.

If this is not the case, the balance backup battery is exhausted and

must be replaced by Precisa Customer Service.

• PASSWORD

PASSWORD

– – – –

DATA-PROTECTION

OFF

DATA-PROTECTION MED

DATA-PROTECTION HIGH

No protection

The configuration menu

is protected

The configuration menu

and the application

menu are protected

NEW PASSWORD ––––

Enter new password

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 38 / 73

Результаты поиска

Содержание XB series

Отзывы: