Precisa XB series Скачать руководство пользователя страница 56

Страница: 56 / 73

■

10 Practical examples

10 Practical examples

10.1 Changing the configuration menu

See Chapter 4.5.1 “Activating the configuration menu”, for the acti-

vation of the configuration menu.

10.1.1 Setting the choice of language

In order to alter the display language, proceed as follows:

10.1.2 Setting the Weight unit

In order to alter the weight unit, proceed as follows:

SPRACHE DEUTSCH

• Press «

MODE

» and hold down

until the currently set language

appears.

• Release the «

MODE

»-button.

LANGUE FRANCAISE

LANGUAGE ENGLISH

• Press «

MODE

» repeatedly, until

the desired language is displayed

(the display will flash).

• Hold down «

MODE

» until entry is

complete (display ceases to flash)

or press «

PRINT

».

• Press «

PRINT

» to exit menu.

unit-1 9

• Press «

MODE

» and hold down

until the currently set unit appears.

• Release the «

MODE

»-button.

unit-1 oz

• Press «

MODE

» repeatedly, until

the desired unit is displayed (the

display will flash).

• Press «

PRINT

» to confirm the

input (display ceases to flash).

• Press «

PRINT

» again to exit menu.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 56 / 73

Результаты поиска

Содержание XB series

Отзывы: