Precisa XB series Скачать руководство пользователя страница 48

Страница: 48 / 73

■

7 Special operating keys

7.2

The Print key «PRINT»

•

Print out an individual value or a report

– Ensure that the balance is in the weighing mode

– Briefly press «

PRINT

– The individual value or report will be printed out.

•

Reset product counter to 1

– Ensure that the balance is in the weighing mode

– Keep «

PRINT

» pressed until “RESET PROD.-COUNTER” is

displayed

– Release «

PRINT

– The product counter will be reset to 1.

•

Print out a balance status

– Ensure that the balance is in the weighing mode

– Keep «

PRINT

» pressed until “PRINT STATUS” is displayed

– Release «

PRINT

– The balance status will be printed out.

•

Print out the application-setup

– Ensure that the balance is in the weighing mode

– Keep «

PRINT

» pressed until “PRINT APPLICATIONS” is displayed

– Release «

PRINT

– The application-setup will be printed out.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 48 / 73

Результаты поиска

Содержание XB series

Отзывы: