Precisa XB series Скачать руководство пользователя страница 66 | Manualshive

Страница: 66 / 73

Precisa XB series Скачать руководство пользователя страница 66

■

14 Further information

64

14.1.3 Set Weighing mode: Auto-Standby

The Auto-Standby mode turns off the balance automatically, if:
• the balance is tared and has shown “Zero” for at least 5 minutes
• the balance has received no remote control command via the inter-

face for at least 5 minutes,

• the automatic zero correction “Auto-Zero” is activated.

It is possible to start the balance again after it has been switched off

by an automatic Auto-Standby:
• Briefly depress any key
• Put a weight on the scale
• Give a remote control command via the interface

14.1.4 Set Weighing mode: Auto-Zero

If the automatic zero correction “Auto-Zero” is activated, the balance

always gives a stable zero (e.g. even with room temperature fluctua-

tions).

14.2 Notes on calibration

The calibration of the balance is fixed in the configuration menu (see

Chapter 3.7 “Calibration of the balance” and Chapter 5.6 “Calibration

functions”).
Possible types of calibration, depending on the model of balance:
• External calibration by means of ICM (Intelligent Calibration Mode)
• External calibration with freely selectable weight
• Internal calibration
• Automatic calibration

NOTE

The calibration can be interrupted at any time by pressing

«

ON/OFF

».

«
...
64
65
66
67
68
...
»

Содержание XB series










































































Отзывы:

Нет отзывов