Precisa XB series Скачать руководство пользователя страница 59

Страница: 59 / 73

10 Practical examples

■

10.2 Selection of an application program

See Chapter 4.5.2 “Activating the application menu” for the activati-

on of the application menu.

10.2.1 Setting for Counting by weighing

For Setup, see Chapter 6.5 “Application “COUNT””

To count uniformly heavy objects such as coins, screws or similar

things, proceed as follows:

SET APP. . . .

• Press «

MODE

» and hold down

button until the currently set ap-

plication appears.

• Release the «

MODE

»-button.

SET APP. count

• Press «

MODE

» repeatedly, until

“SET APP. COUNT” is displayed

(the application will flash).

• Press «

PRINT

» to confirm the

input.

SETup APPlication

• Press «

MODE

» until “SETUP AP-

PLICATION” appears.

• Release the «

MODE

»-button.

Reference 10 pcs

• Press «

MODE

» briefly, the cur-

rently set reference quantity ap-

pears.

• Release the «

MODE

»-button.

Reference

10 pcs

• Press «

MODE

» briefly. The first

digit of the reference quantity will

start to flash.

• Enter the first digit by briefly pres-

sing «

MODE

» repeatedly.

Reference 0

0 pcs

• Press «

MODE

» until the second

digit flashes. Enter the second

digit by briefly pressing «

MODE

repeatedly.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 59 / 73

Результаты поиска

Содержание XB series

Отзывы: