Precisa XB series Скачать руководство пользователя страница 24

Страница: 24 / 73

■

4 Modes of operation and operating

Modes of operation and operating

4.1

Switching on the balance

• Press «

ON/OFF

» to switch on the balance.

The balance carries out a self-diagnosis in order to check the most im-

portant functions. After completion of the start-up process (approxi-

mately ten seconds) “Zero” appears in the display.
The balance is ready for operation and is in the weighing mode.

4.2

Auto-Standby Mode

The balance is equipped with an Auto-Standby mode, which can be

activated or deactivated in the configuration menu.
If the Auto-Standby mode is activated, the balance automatically

switches to Standby some time after the last weighing or key

operation (current-saving function).
The delay before switching to Standby is defined in the configuration

menu (see Chapter 5.7 “Weighing mode”).
• Press any button or put on a weight in order to switch the balance

from the Standby mode back to the weighing mode again.

4.3

Setting and storing the configuration

• Press «

ON/OFF

», to switch on the balance.

• Continue to hold down the «

MODE

» and the «

» button during the

start-up process, until the desired configuration appears on the

display and then release the button:

“FACTORY CONFIG.”: Load factory configuration.
“USER CONFIG.”:

Load user configuration.

“STORE CONFIG.”:

Store present configuration as user configu-

ration.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 24 / 73

Результаты поиска

Содержание XB series

Отзывы: