Precisa XB series Скачать руководство пользователя страница 10

Страница: 10 / 73

■

1 Safety

• If there is any reason to believe that it is no longer possible to

operate the balance without danger, the balance is to be immedia-

tely unplugged from the electricity supply (pull out power adaptor)

and secured against inadvertent operation.

• In carrying out maintenance work, it is essential to heed the recom-

mendations in Chapter 11 “Maintenance and servicing”.

• The balance must not be operated in an area subject to explosion

risks.

• Take care when weighing liquids that no liquid is spilt into the inside

of the balance or into connections on the rear of the equipment or

the power adaptor.

If liquid is spilt on the balance, the latter must immediately be

unplugged from the mains electricity supply (pull out power

adaptor).

The balance may be operated after it has first been re-checked by a

Precisa Service technician.

• The operating instructions must be read by each operator of the

balance and must be available at the workplace at all times.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 10 / 73

Результаты поиска

Содержание XB series

Отзывы: