Precisa XB series Скачать руководство пользователя страница 44

Страница: 44 / 73

■

6 Working with the application menu

6.6

Application “PERCENT”

See Chapter 4.5 “Activating the two main menus” and Chapter 4.6

“How the menu control operates” for the activation of the application

menu.

With the aid of the “PERCENT” program you can display and print out

the weight of different measurements as a percentage of a previously

defined reference weight.

Operation:

Start the application (see Chapter 6.3 “Changing application / weig-

hing mode”).
• Place the reference weight on the weighing pan.
• Press the «

REF

»-button until “REFERENCE 100%” appears on the

display.

• Release the «

REF

»-button.

6.7

Application «Net-Total»

There is no Setup menu for this application.
With the aid of the „NET-TOTAL“ application you can add individual

weighings, where the balance is tared to zero again before each indi-

vidual weighing.

• SETUP

APPLICATION

PERCENT

DECIMALS

AUTO

Enter number of decimal

places

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 44 / 73

Результаты поиска

Содержание XB series

Отзывы: