Precisa XB series Скачать руководство пользователя страница 58

Страница: 58 / 73

■

10 Practical examples

10.1.4 Activation of password protection

The possibilities for setting the password protection are described in

Chapter 5.10 “Password protection”.
In order to activate password protection, proceed as follows:

PASSWORd ––––

• Press «

MODE

» and hold down

button until “PASSWORD ––––”

appears.

• Release the «

MODE

»-button.

PASSWORd

000

• Press «

MODE

» briefly. The first

digit of the password will flash.

• Enter the first digit by briefly pres-

sing «

MODE

» repeatedly.

PASSWORd 7

• Press «

MODE

» until the second

digit flashes. Enter the second

digit by briefly pressing «

MODE

repeatedly.

PASSWORd 7914

• In the same way enter the third

and fourth digit of the password.

• Hold down «

MODE

» until input is

complete (no digit flashing).

DATA-PROTECTION OFF

• Press «

MODE

» briefly. “DATA-

PROTECTION ...” will appear.

• Press «

MODE

» repeatedly, until

the desired data-protection is

displayed (the setting will flash).

new PASSWORd 7914

• Press «

MODE

» and hold down

button until “NEW PASSWORD

7914” appears.

• Release the «

MODE

»-button.

new PASSWORd 1234

• Your own new password can now

be entered in a similar manner to

the foregoing.

PASSWORd ––––

• Press «

PRINT

» to return to

“PASSWORD ––––”.

• Press «

PRINT

» to exit menu.

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 58 / 73

Результаты поиска

Содержание XB series

Отзывы: