Precisa XB series Скачать руководство пользователя страница 43

Страница: 43 / 73

6 Working with the application menu

■

6.5

Application “COUNT”

See Chapter 4.5 “Activating the two main menus” and Chapter 4.6

“How the menu control operates” for the activation of the application

menu.

With the aid of the “COUNT” program you can count items of uniform

weight (screws, balls, coins, etc.).
Depending on the weight and tolerances of the objects to be counted,

you should count a representative number of items for the regulation

of the reference-weight.

Operation:

Start the application (see Chapter 6.3 “Changing application / weig-

hing mode”).
• Place a number of objects on the weighing pan.
• Press the «

REF

»-button until the reference quantity appears on the

display.

• If the reference quantity is correct release the «

REF

»-button.

Otherwise hold down the «

REF

»-button. The pre-defined values will

appear (1, 10, 25, 50, ...). As soon as the desired value appears

release the «

REF

»-button. (The current value can be increased by 1

by briefly releasing and pressing the «

REF

»-button.)

• SETUP

APPLICATION

COUNT

REFERENCE

PCS

Reference-number of

pieces = 10

Содержание XB series










































































Результаты поиска

Содержание XB series

Отзывы:

Precisa XB series, Руководство по эксплуатации, Страница: 43 / 73

Результаты поиска

Содержание XB series

Отзывы: