Pioneer XY-122 Скачать руководство пользователя страница 41

Страница: 41 / 92

3 Rigging And Caster Setting

__________________________________________________________________________________________________________

WARNING:

・

Attach two or more wires to a rigging point different from those for installing the cradle to prevent swaying.

・

The Variable Angle Bracket and the Dual Enclosure Flying Plate Set are not supposed to be used in the following

situations, which may cause an injury or accident.

・

After mounting the speaker with the cradle, never loosen any of its accessory installation screws, since the speaker

could fall or other accidents could occur.

・

Do not attempt to use this product with components other than the specified speaker.

・

Be sure to use the supplied accessory screws.

・

Flat washer and spring washer out of the reach of children and infants. If acidentally swallowed, contact a doctor

immediately.

Suspending

from the wall

Unsymmetry
placement

A deg

B deg

A deg

≠

B deg

Suspending

Over 2 enclosures

NOTE: XY-122 is shown in the illustration.

Suspending from sloped

(non-horizontal) ceiling

http://pioneerproaudio.com/

Page 41 / 92

Содержание XY-122



















































































Результаты поиска

Содержание XY-122

Отзывы:

Похожие инструкции для XY-122

Бренды по названию

Популярные бренды

Pioneer XY-122, Руководство по установке

Результаты поиска

Содержание XY-122

Отзывы:

Похожие инструкции для XY-122

Бренды по названию

Популярные бренды