Pioneer XY-122 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 92

background image

5 Drive unit replacement

___________________________________________________________________________________________________________

Procedure (XY-115S/118S/218S)

Removing and reinstalling the grille.

(1)

(2)

(3)

(4)

Replacement of LF drive unit

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

LF driver units installed in XY-115S and XY-118S are different, but
almost the same procedures can be used to replace both LF drive
units.

Remove the screws from the grille.

12 pieces of screws for XY-115S, 14 pieces of screws for XY-118S
and 24 pieces of screws for XY-218S are required to be removed.

Remove the grille from the enclosure.

Reverse the above steps when placing the grille back to the
enclosure. The grille should be placed back in the same orientation
before it was removed.

XY-218S has 2 LF drive units side by side. Please follow the steps
below to replace one or both of the LF drive unit(s) you want to
replace.

Remove the eight socket head bolts from the LF drive unit.

Lift the LF drive unit up and remove the cables from the LF drive
unit.

Replace the LF drive unit with a new one.

Connect the cables to the two terminals.

Red Terminal (+)

:

Red cable

Black Terminal (-) : Black cable

Ensure that the terminals of the drive unit are placed as shown
below.

CAUTION: The locations of the terminals on XY-115S, 118S and XY-
218S are different. Please see the locations of each drive unit in the
figures below when installing the LF drive unit.

Install the LF drive unit to the enclosure.

Tighten the socket head bolts on the LF drive unit.

Tighten the screw to ensure a solid fit to the grille.

Red Terminal

Black Terminal

NOTE: XY-118S is used in the pictures.

Red Cable

Black Cable

http://pioneerproaudio.com/

Page 72 / 92

©2018 Pioneer DJ CORPORATION

«
...
70
71
72
73
74
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Federal Signal Corporation Страницы: 8

Бренд: KAWNEER Страницы: 4

Бренд: Hanowa Страницы: 6

Бренд: Lampert Страницы: 18

Бренд: Neets Страницы: 16

Бренд: KEF Страницы: 6

Бренд: Daewoo Страницы: 66

Бренд: Easy wave Страницы: 2

Бренд: PartyFunLights Страницы: 4

Бренд: jablotron Страницы: 16

JBL BAR 5.0 MULTIBEAM

Бренд: Harman Страницы: 25

Бренд: Harman Kardon Страницы: 2

Бренд: Harman Kardon Страницы: 3

Бренд: Eaton Страницы: 23

Бренд: Xtrons Страницы: 30

Бренд: Samsung Страницы: 33

TRUE X SPEAKER 1A

Бренд: Yamaha Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды