Pioneer XY-122 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 92

background image

3 Rigging And Caster Setting

___________________________________________________________________________________________________________

3.2.8 Wheel Board

Part list (CP-XY3WB1)

Procedure

(1)

(2)

A wheel board to help with transportation can be attached to the front
of the XY-3B. Lock casters are provided to prevent unexpected
movement with the wheel board. Also, you can use the wheel boards to
stack two enclosures.

Attach the wheel board to the front of the enclosure using the
butterfly latches on both sides of the wheel board. (Fig.3-2-8-A)

Lower down the cabinet so that its back is facing upward. (Fig.3-
2-8-B)

WARNING :

・

When attaching the wheel board to the enclosure, securely

tighten the butterfly latches to the brackets on the sides of the
enclosure.

・

When attaching the wheel board to the enclosure, be sure to

attach it so that the lock caster side is on the bottom side of the
cabinet.

・

The work to raise up and lower down the enclosure for

transportation must be performed by two or more persons. Also,
when raising up the enclosure after transportation, be sure to
lock the lock casters.

・

Be sure to lock the lock casters except during transportation.

Additionally, do not place the enclosures in a sloping location.

・

When stacking, do not se any other method than that specified

in the user's manual. Additionally, do not stack more than three
deep, stack in a sloping location, or stack any products other than
the XY-3B.

・

Stacking work should always be performed by two or more

people.

・

When stacking, apply the locking castor locks firmly.

Additionally, after stacking, check that the guide on the
underside of the wheel board on the upper enclosure is fit firmly
into the enclosure on the underside.

Fig.3-2-8-B

Fig.3-2-8-A

Item

Part Name

Qty

Service Part No.

Note

1

Wheel Board

1

-

Butterfly

latch

Locking Castor

http://pioneerproaudio.com/

Page 50 / 92

©2018 Pioneer DJ CORPORATION

«
...
48
49
50
51
52
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: A SYSTEMS Страницы: 12

VTO2000A Series

Бренд: Dahua Страницы: 16

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 2

Бренд: EAW Страницы: 44

Бренд: EAW Страницы: 2

Бренд: L-Acoustics Страницы: 38

Бренд: L-Acoustics Страницы: 36

Бренд: L-Acoustics Страницы: 31

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 55

Бренд: L-Acoustics Страницы: 201

Бренд: L-Acoustics Страницы: 16

Aqua-Hot AHE-100-04S

Бренд: Vehicle Systems Страницы: 19

Бренд: Yardgard Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды