Pioneer XY-122 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 92

background image

3 Rigging And Caster Setting

__________________________________________________________________________________________________________

(4)

Note:

For larger down-tilt angles, position the pivot on the last hole and

use the point on the rear or underside as a pull-back.

Note:

When hanging the XY-3s using the CP-XY3DF1, the XY-2 can be

attached to the bottom of each enclosure.

WARNING:

・

Attach two or more wire to a rigging point different from those for

installing the CP-XY3DF1 to prevent swaying. (Fig.3-2-4-L)

・

When attaching the XY-2 to the XY-3B, do not attach it to anywhere

other than the bottom of the XY-3B. Make sure to use the included bolt,
washer, and spring washer.

・

Do not suspend anything other than an XY-2 to the bottom of the XY-3B.

Also, do not suspend two or more XY-2s to each of XY-3B.

Ensure the two commercially-available eyebolt are secured to mounting
point on the top of each enclosure to suspend it with wire as a secondary
safety feature. (Fig.3-2-4-M)

For preventing to occur the noise from secondary safety wires, wire
length should be as short as possible.

Combination of Dual Enclosure Flying Plate Set and Variable Angle Bracket

When using the Variable Angle Bracket together with Dual Enclosure Flying
Plate, the 2 enclosures of XY-122/152 stably suspended from the ceiling can be
inclined forward and backward. The angle between the 2 enclosures can be
ranged from 50 degree to 95 degree.

NOTE: All the parts for a combination of Dual Enclosure Flying Plate Set
and Variable Angle Bracket should be compatible with respective
speakers, XY-122 and XY-152.

The range of inclined angle when a CP-XY3DF1 is used to suspend the
speaker from the ceiling is shown in the table below:

To the ceiling

NOTE: XY-122 is shown in the illustration.

Front

Back

Commercially

-available wire

Commercially

-available

eyebolt

Fig.3-2-4-L

Fig.3-2-4-M

Commercially

-available

eyebolt

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Only XY-3B

20

18

14

11

8

5

2

-1

-5

-8

-11

-14

-17

-20

-23

-25

XY-3B + XY-2

16

14

11

9

7

4

2

-1

-3

-6

-8

-11

-13

-15

-18

-20

The mounting point

Angle

[°]

http://pioneerproaudio.com/

Page 40 / 92

©2018 Pioneer DJ CORPORATION

«
...
38
39
40
41
42
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: JBL Страницы: 8

Бренд: Gale Страницы: 16

Бренд: EAW Страницы: 8

Бренд: Zenitel Страницы: 11

Бренд: Zamel Страницы: 11

Бренд: Panasonic Страницы: 89

Бренд: M&K Sound Страницы: 15

Бренд: M-Audio Страницы: 30

Бренд: Dynasound Страницы: 5

Бренд: KYE Systems Corp. Страницы: 15

Бренд: Clarke Страницы: 20

Бренд: Defender Страницы: 93

Бренд: iWantit Страницы: 32

Бренд: Innova Страницы: 36

Бренд: Hama Страницы: 122

Бренд: JBL Страницы: 8

Бренд: Reflex Страницы: 26

Бренд: EDIFIER Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды