Pioneer XY-122 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 92

background image

5 Drive unit replacement

5.1 Two-way loudspeaker

Guide for safe replacement of the drive units

WARNING:

Intended usage

Safety cautions

CAUTION:

Cautions for audio quality

Storage temperature range

Ensure that the LF driver is installed in accordance with the Installation
Manual. Otherwise, your fingers might be caught and get injured during
the installation process.

Inappropriate installation could affect the sound quality.

Do not store speakers at temperatures outside of the rated temperature
range as doing so may cause the speaker to drop in performance or
become damaged.

Storage temperature range: –20 °C to +55 °C (–4 °F to +131 °F)

Do not use the product in locations subject to extreme fluctuations in
temperature. Drastic fluctuation of the temperature and long storage in
the cold temperature might cause small cracks in the magnet of the drive
unit. The performance, reliability and safety for use of this product may
not be affected even if the above issue occurs.

Improper installation of the driver unit could cause them to fall and cause damage or injuries to
persons nearby. Please check the following conditions of all the loudspeakers in the XY series always
before the drive units are replaced.

Do not attempt to use this driver with components other than the
specified loudspeaker.

Certain technical skills and experiences are required to install the driver to
the loudspeaker. Please have the driver installed by qualified professionals.

Ensure that the loudspeaker is placed on a stable place like on a floor. Do
not replace the drivers when it is stacked on other loudspeakers or it is
hung from the ceiling.

Be sure to use and tighten the pre-inserted bolts to the driver installed to
the loudspeaker when you install this driver to the loudspeaker enclosure.

After installation, you must confirm that the bolts and screws used for the
enclosures and the grilles of this product are tightened enough. Periodical
inspections are also required to make sure they are still tightened enough.

http://pioneerproaudio.com/

Page 55 / 92

©2018 Pioneer DJ CORPORATION

«
...
53
54
55
56
57
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: Dali Страницы: 8

Бренд: Tannoy Страницы: 2

Бренд: Olympia Страницы: 5

Бренд: Xilica Audio Design Страницы: 10

Бренд: Fandis Страницы: 8

Бренд: Farfisa Страницы: 72

Бренд: Panasonic Страницы: 45

Xsential QUAD-RO

Бренд: Watermark Страницы: 8

Бренд: Sami Страницы: 2

Бренд: AmeriWater Страницы: 16

Бренд: Abus Страницы: 4

Бренд: Electro-Voice Страницы: 4

Бренд: Amphion Страницы: 11

CARPOWER CRB-130SET

Бренд: Monacor Страницы: 2

Бренд: Vacron Страницы: 17

Бренд: Laars Страницы: 9

Бренд: Valcom Страницы: 3

Бренд: Somogyi Elektronic Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды