Pioneer XY-122 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 92

background image

2 Accessories

__________________________________________________________________________________________________________

Included items

White socket cover seal for the white models

Applicable models:

Procedure

(1)

(2)

(3)

*XY-118S-W is shown in the illustration.

White seal (A) is included inside of the packing box. (Fig.2-1)

Carefully remove the tip of the cover of the double-face tape on the
white label(A), then peel it off.

Place the white seal (A) to fully cover the top of the pole socket. (Fig.2-2)

XY-81-W : 1 piece of white seal is shipped with XY-81-W.
XY-101-W : 1 piece of white seal is shipped with XY-101-W.
XY-122-W : 1 piece of white seal is shipped with XY-122-W.
XY-152-W : 1 piece of white seal is shipped with XY-152-W.
XY-115S-W : 1 piece of white seal is shipped with XY-115S-W.
XY-118S-W : 1 piece of white seal is shipped with XY-118S-W.
XY-215S-W : 2 pieces of white seals are shipped with XY-215S-W.

NOTE: White plastic seals to cover the black pole socket is included in the above models.
A white seal can be attached to an unused black pole socket as you like.
Please follow the instructions below.

Fig.2-2

(A)

Pole socket

Fig.2-1

(A)

Part list

Item

Part Name

Qty Service Part No. Note

1

Pole cover

1

08A501

-

http://pioneerproaudio.com/

Page 10 / 92

©2018 Pioneer DJ CORPORATION

«
...
8
9
10
11
12
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: CABASSE Страницы: 16

Бренд: EarthQuake Страницы: 16

Бренд: Zadako Страницы: 15

Бренд: V-Tec Страницы: 16

Бренд: Magnavox Страницы: 24

Бренд: Magnavox Страницы: 22

Бренд: Magnavox Страницы: 21

Magnavox FW 750C

Бренд: Magnavox Страницы: 28

Magnavox FW 2012

Бренд: Magnavox Страницы: 16

Бренд: Magnavox Страницы: 2

MME239 - Micro DVD Home Theater System

Бренд: Magnavox Страницы: 39

Бренд: Sanlien Страницы: 42

Бренд: dallmeier Страницы: 2

Бренд: Samsung Страницы: 29

Бренд: Aiphone Страницы: 2

Бренд: Image Dynamics USA Страницы: 2

Бренд: Insignia Страницы: 28

Бренд: Karaoke USA Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды