Pioneer XY-122 Скачать руководство пользователя страница 31

Страница: 31 / 92

3 Rigging And Caster Setting

__________________________________________________________________________________________________________

WARNING:

・

Do not attempt to use this product with components other than the specified speaker.

・

Be sure to use the supplied accessory screws.

・

Flat washer and spring washer out of the reach of children and infants. If acidentally swallowed, contact a doctor

immediately.

・

After mounting the speaker with the cradle, never loosen any of its accessory installation screws, since the speaker could

fall or other accidents could occur.

・

Attach two or more wires to a rigging point different from those for installing the cradle to prevent swaying.

・

Variable Angle Bracket is not supposed to be used in the following situations,

which may cause an injury or accident.

Fig.3-2-3-A

Plus
degree

Suspending

from the wall

Suspending

Multiple enclosures

Minus
degree

Suspending from sloped

(non-horizontal) ceiling

Back

NOTE: XY-122 and CP-XY12AB1 is used in the illustration below.

http://pioneerproaudio.com/

Page 31 / 92

Содержание XY-122



















































































Результаты поиска

Содержание XY-122

Отзывы:

Похожие инструкции для XY-122

Бренды по названию

Популярные бренды

Pioneer XY-122, Руководство по установке

Результаты поиска

Содержание XY-122

Отзывы:

Похожие инструкции для XY-122

Бренды по названию

Популярные бренды