Pioneer XY-122 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 92

background image

1 Introduction

____________________________________________________________________________________________________________

1.3 System set-up

WARNING

・

・

Stand mounting

・

・

Ensure your stand height is locked off and the tripod legs are positioned so as to be stable.

・

Ensure to take overturn preventing measure and fall preventing measure.

・

Check the weight loading of your stands and adapters before attempting to mount the loudspeaker.

・

Do not stack a second loudspeaker on top of the stand-mounted one.

・

When using poles on top of subwoofer systems, please observe similar precautions.

Pole-mounted full-range loudspeakers from the XY-115S, XY-118S and XY-215S

・

・

Ensure the M20 pole is screwed in tightly, your stand height is locked off and the system is stable.

・

Do not stack a second loudspeaker on top of the stand-mounted one.

Note:

When you want to combine the XY-81, XY-101, XY-122 or XY-152 enclosure with the XY-115S, XY-118S or Y-
215S enclosure, ensure you use a commercially-available pole, where one of the edge is M20 threaded and
the other is 35mm diameter as shown below.

Loudspeaker systems are potentially dangerous objects if used incorrectly. Please ensure that you read this section
fully, and contact your local dealer should you be in any doubt over correct operation procedures.
Professional loudspeaker systems are capable of producing damage-inducing sound pressure levels, and hence care
should be taken when setting your system up, particularly when it comes to loudspeaker placement within a venue.
Damage to the ear can result from levels above 90 dB under prolonged exposure.

The XY-81, XY-101, XY-122 and XY-152 can be mounted on a loudspeaker stand using the equipped polemount adapter
for a standard 35 mm (1.4 in.) loudspeaker stand.
The XY-2 can be mounted on loudspeaker stand using polemount adapter which fits both for hole of 13mm diameter
and for a standard 35 mm (1.4 in.) loudspeaker stand.
When mounting in this way, please consider the following:

・

Ensure cables are run so as to leave enough slack to enable neat wiring, and thus reduce the risk of the speaker

being pulled over. Loose cables should be covered or taped down wherever possible to reduce trip hazards.

The XY-115S, XY-118S and XY-215S can support other loudspeakers using an M20 threaded pole adapter. When
mounting in this way, please consider the following:

・

Ensure cables are run so as to leave enough slack to enable neat wiring, and thus reduce the risk of the speaker

being pulled over. Loose cables should be covered or taped down wherever possible to reduce trip hazards.

XY-115S/XY-118S XY-215S

XY-81/XY-101

XY-122/XY-152

XY-115S/XY-118S/XY-215S

M20 screw threaded pole socket

M20 screw

threaded pole

35mm pole

XY-81/XY-101/XY-122/XY-152

bottom

35mm pole socket

http://pioneerproaudio.com/

Page 7 / 92

©2018 Pioneer DJ CORPORATION

«
...
5
6
7
8
9
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Concord express

Бренд: GE Страницы: 3

Concord express

Бренд: GE Страницы: 32

Beosound Explore

Бренд: Bang & Olufsen Страницы: 4

Бренд: Fender Страницы: 3

SET-2000 Oil/Sludge

Бренд: Labkotec Страницы: 14

Бренд: LAON TECHNOLOGY Страницы: 58

Бренд: Oklahoma Sound Страницы: 2

Бренд: Oklahoma Sound Страницы: 13

Бренд: X10 Страницы: 4

Бренд: MAC TOOLS Страницы: 30

STExB2X05-S Series

Бренд: E2S Страницы: 20

Бренд: Abbyson Страницы: 7

Бренд: Polk Mono Страницы: 86

Бренд: V-Tec Страницы: 15

THX Select Series

Бренд: SensaSound Страницы: 14

Бренд: Bigben Страницы: 56

Бренд: Monitor Audio Страницы: 13

Бренд: S Fire Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды