Pioneer XY-122 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 92

background image

3 Rigging And Caster Setting

_________________________________________________________________________________________________________

Procedure (CP-XY8VC1/XY10VC1/XY12VC1/XY15VC1)

(1)

Only XY-152

(2)

Remove the pre-inserted mounting screws from the top of
enclosure. The number of screws to be removed from XY-
81/101/122 is 2 (The location is shown in Fig.3-2-1-A) and from
XY-152 is 4.

NOTE: In addition, Using the supplied two M10 socket
head bolts(E), align the mounting holes in the load
plate(F) with the mounting point on the top of the
enclosure. Tighten the bolts over 15N·m torque. (Fig.3-2-
1-B)

Using the supplied two bolts(B), align the mounting holes in the
inner yoke of the Vertical Flying Cradle(A) with the mounting
points on the top of the enclosure. The installation method
depends on the model you use. Please follow the steps below
for further details when installing such a model. (Fig.3-2-1-C)

XY-81:
Using the supplied two M8 countersunk bolts(B), align the
mounting holes in the inner yoke of the Vertical Flying Cradle(A)
with the mounting points on the top of the enclosure. Tighten
the bolts over 7N·m torque.

NOTE: XY-122 is shown in the illustrations below.

Fig.3-2-1-A

(A)

(B

(D)

(C)

(C)

(D)

Fig.3-2-1-B

(E)

(F)

http://pioneerproaudio.com/

Page 22 / 92

©2018 Pioneer DJ CORPORATION

«
...
20
21
22
23
24
...
»

Содержание XY-122





























































































Отзывы:

Нет отзывов

Похожие инструкции для XY-122

Бренд: Canon Страницы: 12

Бренд: Wayne Страницы: 16

Бренд: Ultrasonic Страницы: 16

Aqua-Pure AP510

Бренд: 3M Страницы: 16

Бренд: Dahua Страницы: 22

Бренд: Fender Страницы: 3

CONCORD Express

Бренд: GE Interlogix Страницы: 32

Бренд: Garmin Страницы: 10

Бренд: Discount Car Stereo Страницы: 5

Pack TYXAL+ Access

Бренд: DELTA DORE Страницы: 11

Бренд: Cyrus Страницы: 6

Бренд: Hiltron Страницы: 64

Бренд: Trailer Vision Страницы: 18

Бренд: DAPAudio Страницы: 12

Бренд: JBL Страницы: 16

Бренд: Daewoo Страницы: 38

ICAD GSX-L208BTB

Бренд: Gemini Страницы: 8

Бренд: Fbt Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды