PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 98

Страница: 98 / 248

- Prepare the fitting surface using the recommen-

ded product applying a thin layer after degreasing

the surface with a suitable solvent (e.g. trichloro-

ethylene)

Recommended products

Loctite 510

Liquid sealant

Gasket

- Assemble the equipment need to close the crank-

case half (screws, wrench).

- Heat the crankcase half on the flywheel side us-

ing the thermal gun, with the same procedure on

the transmission side crankcase half.

- Keep the transmission side crankcase half in hor-

izontal position to introduce the flywheel side

crankcase half with a firm and precise move.

N.B.

WEAR GLOVES WHEN HANDLING THE
CRANKCASE HALF. DO NOT USE RAGS FOR
THIS OPERATION

- Insert at least 3 fixing screws and tighten quickly.

- Insert 5 more screws and tighten at the prescribed torque.

Locking torques (N*m)

Crankcase closing screws:

12 -13 Nm

Engine

NRG Power Purejet

ENG - 34

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 98 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: