PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 146

Страница: 146 / 248

- ON to allow switching to the stored sta-

tus.

P1125

TPS1

TPS1 signal missing. Acknowledge-

ment occurs when the signal voltage is

close to:

0V = short circuit

5V = open circuit

Free

P1128

TPS2

TPS2 signal missing. Acknowledge-

ment occurs when the signal voltage is

close to:

0V = short circuit

5V = open circuit

Free

P1120

TPS OFFSET

The voltage of both TPS signals in not

as expected. The fault is recognised by

comparing the signals with the power

supply polarity

Stays idle

P1124

TPS1OFFSET

The voltage of TPS1 signal in not as ex-

pected. The fault is recognised by com-

paring the signals with the TPS1 power

supply polarity

Free

Off

P1127

TPS2

The voltage of TPS2 signal in not as ex-

pected. The fault is recognised by com-

paring the signals with the TPS2 power

supply polarity

Free

Off

P1560

SENSOR

VOLTAGE

The TPS sensor and coolant tempera-

ture sensor power supply voltage do not

meet specs.

Off

P1561 (*)

VOLTAGES

SENSOR 2

The TPS sensor and temperature sen-

sor power supply voltage does not meet

specs. Too high voltages may be rec-

ognised.

Forced idle

If one or more errors are detected, or differences are detected between the values shown in the pa-

rameters, check the circuit and sensor using the troubleshooting procedure.

1. Install the interface wiring ECU.

Specific tooling

020481Y

Control unit interface wiring

Omit the connection to the ECU. Disconnect the connector of sensor TPS and of the coolant temper-

ature sensor.

pure jet injection

NRG Power Purejet

INJ PJ - 30

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 146 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: