PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 109

Страница: 109 / 248

Refitting

When refitting, tighten to the prescribed torque and

apply the recommended grease to the threaded

cone.

Recommended products

AGIP GREASE PV2

Grease for control levers

on the engine

White anhydrous-calcium based grease to protect

roller bearings; temperature range between -20 °

C and +120 °C; NLGI 2; ISO-L-XBCIB2

Locking torques (N*m)

Locking torque:

65 to 70 N•m

Front fork

Removal

- Remove the front brake calliper.

- Remove the odometer cable from the reduction

gear box.

- Remove the front mudguard.

- Remove the handlebar.

After removing the steering ring-nut using the spe-

cial tool, lean the vehicle on one side and extract

the steering tube.

Specific tooling

020055Y

Wrench for steering tube ring nut

See also

Front brake calliper
Handlebar

Overhaul

Disassemble damper

NRG Power Purejet

Suspensions

SUSP - 3

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 109 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: