PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 91

Страница: 91 / 248

- Remove the air injector

- The carbon dam ring must be broken to be re-

moved.

- Carefully clean the air injector and the seat re-

moving any carbon residues.

- Check that the sealing rings exhibit no wear, or

replace them.

- To refit, use a new carbon dam ring.

- Use the specific tool to fit the carbon dam ring.

We recommend doing this in several steps to en-

sure a correct widening of the ring as shown in the

photo.

Specific tooling

020615Y

Carbon dam ring fitting kit

- Position the specific tool with the rung facing the

injector as shown in the figure.

- Use the specific tool to tighten the carbon dam

ring seat as shown in the figure.

- Take several steps to ensure a correct insertion

into the seat.

- Refit the air injector in its seat on the head quickly

to prevent the carbon dam ring from expanding

again.

Specific tooling

020615Y

Carbon dam ring fitting kit

Crankcase - crankshaft

• Remove flywheel and stator

- Remove the driving pulley

- Remove the driven pulley

- Remove the mixer

NRG Power Purejet

Engine

ENG - 27

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 91 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: