PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 248

PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 122

6. The diagnostic tester is ready for use. The selected software will stay in memory also for the next

uses

N.B.

IF THE SCOOTER DIAGNOSTIC TESTER IS NOT LOADED WITH THE SYSTEM SOFTWARE, UP-
GRADE WITH A PC, THE PROGRAMMING KIT AND THE SOFTWARE TO LOAD. SET THE
DIAGNOSTIC TESTER TO FUNCTION «LINK TO PC» IN THE MENU.

The main menu of the diagnostic tester has the following functions:

• PARAMETERS

• ERRORS

• PARAMETERS STORED

• ERROR CLEARING

• ACTIVE DIAGNOSTIC

• TPS RESET

• CALIBRATION

• ECU INFORMATION

To access the individual functions, the tester must be connected to the vehicle diagnostic outlet and

the ECU must be on.

• To connect the scooter diagnostic tester, raise

the seat

• Remove the left detail shown in the figure

• Extract the grip from the support clip

pure jet injection

NRG Power Purejet

INJ PJ - 6

«
...
120
121
122
123
124
...
»

Содержание NRG POWER PUREJET

























































































































































































































































Отзывы:

Нет отзывов