manualshive.com logo in svg

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 133 / 248

Поделиться
Скачать
PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 133

Specific tooling

020460Y

 

Scooter diagnosis and tester

10- Measure the battery voltage.

GO TO point 11

GO TO point 12

11- Voltage is lower than 8.5 V. Recharge the battery.

GO TO point 15

12- The battery voltage is between 8.5 and 14.5 V

GO TO point 18

13- The ECU supplies are currently present. For a complete check, perform the check as described at

point «A»

14- The ignition light did not switch on. The fuel pump is not activated. When connecting the diagnostic

testers, the following message appears: «the ECU does not respond, check all connections».

GO TO point 19

Specific tooling

020460Y

 

Scooter diagnosis and tester

15

- Check the charger.

GO TO point 

17

16

- The ECU supplies are conform.

17

- Check all electrical installation connections for any possible problems that are related to loosening

or oxidation.

GO TO point 

20

18

- Check the main supply.

GO TO point 

20

19

- Check the power supply to panel.

GO TO point 

20

20

- Prepare the interface wiring with adapter 3. Install the specific tool as described here:

- Remove the 20A fuses

- Disconnect the connector from the ECU

- Connect the specific tool to the vehicle installation, not connecting the ECU

- Re-connect the 20A fuse

This toll, mounted this way, allows all checks on the installation sections

GO TO point 

21

Specific tooling

020481Y

 

Control unit interface wiring

NRG Power Purejet

pure jet injection

INJ PJ - 17

Содержание NRG POWER PUREJET

























































































































































































































































Отзывы:

Нет отзывов