PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 76

Страница: 76 / 248

Removing the hub cover

• Remove the transmission cover

• Remove the clutch assembly

• Discharge the rear hub oil.

• Remove the 5 screws indicated in the figure.

• Remove the hub cover with driven pulley shaft.

See also

Refitting the clutch

Removing the wheel axle

- Remove the intermediate gear and the complete

gear wheel axle.

- When removing the intermediate gear pay atten-

tion to the various shim adjustments.

Removing the wheel axle bearings

- Remove the oil seal and the seeger ring.

- Remove the bearing by pushing from the outside

towards the inside of the gear compartment, using

the appropriate punch.

Specific tooling

020363Y

20 mm guide

020376Y

Adaptor handle

020358Y

37x40-mm adaptor

Engine

NRG Power Purejet

ENG - 12

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 76 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: