PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 112

Страница: 112 / 248

- Only remove the seats if it is strictly necessary.

- Using the special tool remove the upper fifth

wheel seat by putting the special tool into the lower

part of the headstock as indicated in the figure.

- By inserting the punch into the top of the tube,

remove the lower fifth wheel seat from the head-

stock.

Specific tooling

020004Y

Punch for removing fifth wheels from

headstock

Refitting

Lower and upper races from frame refitting

- Using the special tool, refit the upper and lower

bearing seats on the headstock.

Specific tooling

001330Y

Tool for fitting steering seats

Steering bearing

Removal

Disassemble steering locking ring nut

- Remove the handlebar.

- Remove the bearing of steering ring nut using the

specific tool.

Specific tooling

020055Y

Wrench for steering tube ring nut

See also

Handlebar

Suspensions

NRG Power Purejet

SUSP - 6

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 112 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: