PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 248

PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 61

hours. The connections with the power supply source must be made by connecting the corresponding

poles (+ with + and - with -). The battery caps must be removed during charging.

Specific tooling

020333Y

Single battery charger

020334Y

Multiple battery charger

4) Cleaning the battery

The battery should always be kept clean, especially the upper part, and the terminals protected with

vaseline.

CAUTION

NEVER USE FUSES WITH A CAPACITY HIGHER THAN THE RECOMMENDED CAPACITY. USING
A FUSE OF UNSUITABLE RATING MAY SERIOUSLY DAMAGE THE VEHICLE OR EVEN CAUSE
A FIRE.

CAUTION

IN EMERGENCIES, THE CHARGING TIME CAN BE DECREASED TO 5-6 HOURS.

CAUTION

ORDINARY AND DRINKING WATER CONTAINS MINERAL SALTS THAT ARE HARMFUL FOR
THE BATTERY. FOR THIS REASON, YOU MUST ONLY USE DISTILLED WATER.

CAUTION

CHARGE THE BATTERY BEFORE USE TO ENSURE OPTIMUM PERFORMANCE. INADEQUATE
CHARGING OF THE BATTERY WITH A LOW LEVEL OF ELECTROLYTE BEFORE IT IS FIRST
USED SHORTENS THE LIFE OF THE BATTERY.

NRG Power Purejet

Electrical system

ELE SYS - 17

«
...
59
60
61
62
63
...
»

Содержание NRG POWER PUREJET

























































































































































































































































Отзывы:

Нет отзывов