PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 79

Страница: 79 / 248

Refitting the ub cover

• Refit the complete wheel axis.

• Refit the intermediate gear being careful of the

two shim adjustments.

• Apply LOCTITE 510 for surfaces on the hub cov-

er and refit it with the complete pulley shaft.

• Insert the 5 screws and tighten them to the pre-

scribed torque.

N.B.

CLEAN THE CONTACT SURFACES OF THE
HUB COVER AND THE HALF CRANKCASE OF
RESIDUE FROM PREVIOUS GASKETS BE-
FORE APPLYING A NEW ONE.

Locking torques (N*m)

Locking torque:

11 to 13 Nm

Flywheel cover

Removing the stator

- Remove the flywheel cover.

• Use a specific compass wrench and a 15 mm

Allen wrench to remove the flywheel lock-nut.

Specific tooling

020565Y

Flywheel lock calliper spanner

NRG Power Purejet

Engine

ENG - 15

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 79 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: