manualshive.com logo in svg

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 123 / 248

Поделиться
Скачать
PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 123

• Remove the cover from the diagnostic grip

• Connect the diagnostic tester wiring

• Connect the power supply cable with battery ter-

minals to the diagnostic tester

• Connect the terminals to the battery respecting

the polarity: RED (+) - BLACK (-)

N.B.

FAILURE TO DO SO MAY PERMANENTLY IM-
PAIR THE DIAGNOSTIC TESTER

• To disconnect the tester, remove the terminals from the battery

• Remove the connector from the outlet

• Reapply the protection cap to the outlet to prevent dirt from laying onto the contacts

• Refit the battery cover

PARAMETETERS

Specification

Desc./Quantity

ENGINE RPM

Displays the regime of the engine in all conditions,

including the start-up

ENGINE TEMP. °C

Indicates the coolant temperature

THROTTLE OPEN. %

Indicates the % of opening of the throttle valve

T. FUEL INJECT. MS

Time of opening the fuel injector

AIR INJECTION T. MS

Time of opening the air injector

(air- fuel spray)

ADVANCE IGN. °

Advance ignition in degrees before the TDC

NRG Power Purejet

pure jet injection

INJ PJ - 7

Содержание NRG POWER PUREJET

























































































































































































































































Отзывы:

Нет отзывов