PIAGGIO NRG POWER PUREJET Скачать руководство пользователя страница 92

Страница: 92 / 248

- Remove the throttle body with manifold, diaphragm, gasket and blade support

- Remove the volumetric compressor

- Remove the thermal unit

- Remove the starter

See also

Removing the driven pulley
Removing the driving pulley
Cylinder assy. and timing system
Removal

Splitting the crankcase halves

- Remove the 8 crankcase half clamping screws

shown in the figure

- Insert the guard on the crankshaft as shown in

the figure.

- Use the specific tool to remove the crankcase half

on the flywheel side. Place the tool being careful

to correctly centre it

- Use a 17 mm Allen wrench to remove the crank-

case half on the flywheel side.

N.B.

IF SEPARATION REQUIRES FORCING, USE A
THERMAL GUN TO HEAT THE CRANKCASE IN
THE BENCH BEARING ZONE

Specific tooling

020151Y

Air heater

020163Y

Crankcase splitting plate

Engine

NRG Power Purejet

ENG - 28

Содержание NRG POWER PUREJET

























































































































































































































































Результаты поиска

Содержание NRG POWER PUREJET

Отзывы:

PIAGGIO NRG POWER PUREJET, Руководство по ремонту, Страница: 92 / 248

Результаты поиска

Содержание NRG POWER PUREJET

Отзывы: