PIAGGIO 633929(IT) Скачать руководство пользователя страница 96

Страница: 96 / 314

This section describes the operations to be carried out on the engine and the tools to be used.

Automatic transmission

Transmission cover

- To remove the transmission cover it is necessary

to remove the plastic cover first, by inserting a

screwdriver in the slotted holes. Using the clutch

bell lock wrench shown in the figure, remove the

driven pulley shaft locking nut and washer.

Specific tooling

020423Y

driven pulley lock wrench

- Remove the cap/dipstick from the engine oil filling

hole.

- Remove the ten screws.

- Remove the transmission cover.

If this operation is carried out directly on the vehi-

cle, remove the cooling air supply coupling of the

transmission housing.

Air duct

- Remove the five screws on two different levels

as well as the small casing.

Engine

MP3 125

ENG - 2

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 96 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: