PIAGGIO 633929(IT) Скачать руководство пользователя страница 71

Страница: 71 / 314

A. Left turn indicator bulbs

B. Stop light bulb

C. Tail light bulb

30.

Licence plate lamp

31.

Rear right turn indicator

A. Tail light bulb

B. Stop light bulb

C. Right turn indicator bulbs

32.

Front left turn indicator

33.

Headlight assembly

A. Tail light bulbs

B. Low-beam bulb

C. High-beam bulb

34.

Front right turn indicator

36.

Remote control headlight

37.

Light switch

48.

Parking electronic control unit

56.

Instrument panel

Checks and inspections

This section is devoted to the checks on the electrical system components.

Immobiliser

The electric ignition system is fed with direct cur-

rent and is protected by an anti-theft immobilizer

integrated to the control unit.

The ignition system consists of:

- electronic control unit

- immobilizer aerial

- master and service keys with built-in transponder

- H.V. coil

- diagnosis led

The diagnosis led also works as a blinking light to

deter theft. This function is activated every time the

key switch is turned to "OFF" and it remains active

48 hours so as not to damage the battery charging

process.

MP3 125

Electrical system

ELE SYS - 11

Содержание 633929(IT)



























































































































































































































































































































Результаты поиска

Содержание 633929(IT)

Отзывы:

PIAGGIO 633929(IT), Руководство по обслуживанию станции, Страница: 71 / 314

Результаты поиска

Содержание 633929(IT)

Отзывы: